Electronics etc
-
ARCELI DC to DC step down ()
This constant voltage and constant current programmable control power supply module makes analog integration and digital control functions combined in one.The output voltage is adjustable from0-50.00V, the output current is adjustable from 0-15.00A,Output Power0-1000W.Advanced function, good visual effect, high operability, high precision.
Add to Cart2.98€ -
22402A-18 protoboard one side 5X7 cm ()Quality PCB prototype board high quality glass fiber, Sturdy material. Well etched and well drilled. The holes are centered well and all pads are nicely tinned, when you stack the boards up you can see clear through. Tinned plated finish prevents oxidation, not easy to deformAdd to Cart3.45€
-
1.5V 1.8V 2.5V 3V 3.3V 3.7V 4.2V to 5V DC-DC Step Up Module 5V ()5V output version:
The input voltage is 0.9-5v; Output Voltage 5V
Output current: 480ma
Starting voltage 0.8V, output current 7ma
Input 1-1.5v, output 5V, 40-100ma;
Input 1.5-2v, output 5V, 100-150mA;
Input 2-3v, output 5V, 150-380ma;
Input over 3V, output 5V 380-480ma;Add to Cart2.62€ -
Aluminum Heatsink Cooler 8 x 8 x 4mm Adhesive Kit for Cooling Raspberry Pi ()Description: 8 x 8 x 4mm Aluminum Heatsink
Features:
Brand New and High Quality!
These heatsinks have a layer of thermal adhesive that allow for easy installation on to your board..
Just peel and stick.
Reduce the risk of hardware failure due to overheating.
Installation Instructions:
Make sure the chip modules are free from dirt and grease
Peel the protective liner off on the base of the heatsink
Apply the heatsinks to the corresponding chip modules and apply firm pressure.Add to Cart1.18€ -
mini 1.8V 3V 3.7V 5V to 3.3V Boost & Buck Low Noise Regulated Charge Pump DC/DC Converter ()
- Supply Voltage:
Low Noise, Regulated Charge Pump DC/DC Converter
2 in 1 DC-DC Step-Down & Step-Up Converter module
Fixed 3.3V+-4% Output
Voltage Input Range: 1.8~5V
Long time maximum output current 100mA
Short time maximum output current 150mA
working frequency 1.2MHz.
Short-Circuit Protection
No load input current : 0.65mA
2.54mm pin pitch, Arduiuo Breadboard MCU Development Board friendly
Excluding Pin Size 11mm x 7.62mm x 4.5mm(small)
Weight : about 0.5g(Very very light)
Applications:Low Power Wifi Module:ESP8266Low-power Bluetooth module : HC-05 HC-06Low-power Wireless UART module : HC-11 HC-12Low-power wireless module : CC1101 CC2500 Nrf24l01+Low-power LED Driver2 AA Cell to 3.3VUSB On-The-Go DevicesHandheld Devices
Add to Cart1.79€ -
22402A-17 protoboard two sided 3x7 cm ()Quality PCB prototype board high quality glass fiber, Sturdy material. Well etched and well drilled. The holes are centered well and all pads are nicely tinned, when you stack the boards up you can see clear through. Tinned plated finish prevents oxidation, not easy to deformAdd to Cart3.45€
-
HT7333-A 7333-A HT7333 HT7333A-1 TO92 Low Power Consumption LDO ()Features Ultra low quiescent current: 4A (typ.)
High input voltage (up to 12V)
Output voltage: 3.3V
Output voltage accuracy: tolerance 3%
Maximum output current: 250mA
Low dropout voltage Low temperature coefficient
FeaturesUltra low quiescent current: 4mA (typ.) High input voltage (up to 12V) Output voltage: Maximum output current: 250mA Low dropout voltage Low temperature coefficient TO-92, SOT-89 package
ApplicationsBattery-powered equipment Voltage regulator for microprocessor Voltage regulator for LAN cards Wireless Communication equipment Audio/Video equipment
The HT73XX series is a set of three-terminal, low power, high voltage regulators implemented in CMOS technology. The series features extremely low quiescent current which is typically 4mA. They allow input voltages as high as 12V. The device provides large current with a significantly small dropout voltage. The HT73XX consists of a high-precision voltage reference, an error correction circuit, and a current limited output driver. They are available with several fixed output voltages ranging from to 5.0V. CMOS technology ensures low dropout voltage and low current consumption. Although designed primarily as fixed voltage regulators, these devices can be used with external components to generate variable voltages and currents.
Add to Cart0.83€ -
4 Channel 5V Relay Module Arduino Compatible ()100% brand new and high quality
5V 4-Channel Relay interface board,and each one needs 15-20mA Driver Current
Standard interface that can be controlled directly by microcontroller
Equipped with high-current relay,AC250V 10A,DC30V 10A
Indication LED for Relay output status
Add to Cart5.36€ -
Voltage regulator 3.3V HT7333-A 7333-A HT7333 HT7333A-1 TO92 Low Consumption LDO New Original ()The HT73xx-7 is a low power high voltage series of regulators implemented in CMOS technology which has the advantages of low voltage drop and low quiescent current. They allow input voltages as high as 30V and are available with several fixed output voltages ranging from 2.1V to 5.0V. When the CE input is low, a fast discharge path pulls the output voltage low via an internal pull-down resistor. An internal over-current protection circuit prevents the device from damage even if the output is shorted to ground. An over-temperature protection circuit ensures the device junction temperature will not exceed a temperature of 150°C.
Output Type Fixed Voltage - Output (Min/Fixed) 3.3V Output Configuration Positive Voltage - Input (Max) 12V Operating Temperature -40℃~+85℃ (TA) Current - Output 250mA Voltage Dropout (Max) 90mV @ 40mA (typ) Add to Cart0.83€ -
22402A-18 protoboard two sided 5x7 cm ()Quality PCB prototype board high quality glass fiber, Sturdy material. Well etched and well drilled. The holes are centered well and all pads are nicely tinned, when you stack the boards up you can see clear through. Tinned plated finish prevents oxidation, not easy to deformAdd to Cart3.45€
-
22402A-17 protoboard two sided 6x8 cm ()Quality PCB prototype board high quality glass fiber, Sturdy material. Well etched and well drilled. The holes are centered well and all pads are nicely tinned, when you stack the boards up you can see clear through. Tinned plated finish prevents oxidation, not easy to deformAdd to Cart3.45€
-
3 x AA Battery Holder with wire ()This 3 "AAA" battery holder holds the batteries side-by-side and delivers 4.5 VDC. It's ideal to use as a replacement or for project use.Add to Cart2.26€
-
Aluminum Heatsink Cooler 14 x 14 x 6mm Adhesive Kit for Cooling Raspberry Pi ( Copy ) ()Description: 14 x 14 x 6mm Aluminum Heatsink
Features:
Brand New and High Quality!
These heatsinks have a layer of thermal adhesive that allow for easy installation on to your board..
Just peel and stick.
Reduce the risk of hardware failure due to overheating.
Installation Instructions:
Make sure the chip modules are free from dirt and grease
Peel the protective liner off on the base of the heatsink
Apply the heatsinks to the corresponding chip modules and apply firm pressure.Add to Cart1.49€ -
2 x AA Battery Holder with wire ()This 2 "AAA" battery holder holds the batteries side-by-side and delivers 3 VDC. It's ideal to use as a replacement or for project use.Add to Cart2.02€
-
DC-DC Automatic Buck Boost Power Module Step Up and Down Board Input 3-15V Output 3.3V ()
- Type:
- Condition:
- Application:
- Supply Voltage:
- Dissipation Power:
- Model Number:
Feature:The DC-DC power module is automatically buck-boost to support the shutdown function.The maximum input voltage is 15VDC, the quiescent current is less than 200uA, the fixed output is 3.3V and the maximum output current is 600mA.Design work frequency of up to 1.2MHz, high stability, cost-effective, all industrial-grade components, long working voltage drift-free, suitable for demanding applications.Application:Widely used in communications equipment, digital radio, industrial motherboards, toys, model aircraft, microcontroller motherboards, household electrical appliances, automotive power supply, security monitoring, field collection, street lamps.Parameters:Input voltage: 2.5V-15VMaximum current: 600mAOutput voltage: 3.3VMaximum efficiency: 75%Package Included:
1 x DC-DC Automatic Buck Boost Power Module
Add to Cart5.36€ -
HX1838 Infrared Remote Control Module IR Receiver Module DIY Kit HX1838 for Arduino Raspberry Pi ()
PRODUCT DESCRIPTION
1 VCC external 3.3V-5V voltage (can be directly connected with the 5V MCU and 3.3V chip)2 GND external GND
3 IN external microcontroller I/O port, I/O port has been designed with 10K pull-up resistor
Theoretical test suite from 5-8 meters, but the surrounding environmental factors depends on when you use the actual application and intermediate barrier (e.g. diaphragm, glass, hinder the barrier or other materials), receiving head using HX1838, with a power indicator light, can receive the 38K frequency of any remote control coding data!
PRODUCT FEATURE
1, sensor using HX1838, high sensitivity
2, working voltage 5V
3, output: digital output
PACKAGE INCLUDED1×Infrared Remote Controller Kit
Add to Cart4.75€ -
PL2303HX USB to TTL Download Module ()
Features:
1. Using the new control chip PL2303HX, it can brush the machine at high speed and stably
2. With 500mA self-recovery fuse overcurrent protection
3. Set two data transmission indicators to monitor the data transmission status in real time
4. Brush 3.3V and 5V pin interface, convenient for different voltage system machines that need power supply
5. The interface pin header is parallel to the board, instead of being installed perpendicular to the board, which is convenient for the DuPont line when flashing.
6. The entire circuit board is covered with transparent heat-shrinkable tubing, so that the PCB circuit board and the entity form an independent state, thereby protecting the board metal from sudden explosion and burning. Due to the use of transparent materials, there is no interface for screen silk screen viewing and indicator monitoring effects
7. Support WIN7 systeAdd to Cart3.21€ -
22402A-18 protoboard two sided 4x6 cm ()Quality PCB prototype board high quality glass fiber, Sturdy material. Well etched and well drilled. The holes are centered well and all pads are nicely tinned, when you stack the boards up you can see clear through. Tinned plated finish prevents oxidation, not easy to deformAdd to Cart3.45€
-
5V Power Bank circuit board ()Product Features:1.4-level LED lamp display power, not working state intelligent automatic shutdown;2. Built-in lithium battery protection IC, over-current, overpressure, undervoltage protection;3. Dual USB output;4, motherboard size: Thick 8mm* width 32mm* long 69mm.Product Basic Parameters:Input port: MicroUSB (Andro)Input requirements: 5V constant voltage power supply can do charge input power, the most matching charger for 5v1a aboveOutput port: USBOutput parameters: 5V1A/5V2ARequirements for rechargeable batteries:Available Batteries: 18650 batteries, cell phone batteries, flat-panel batteries, MP3 batteries, etc. 3.7v-4.2V polymer Lithium battery, can be a single section (piece) power supply, can also be multiple sections (tablets) parallel power supply (not supported in series, not in series). (Note: Parallel increase in capacity, series is to increase the voltage, only in parallel!) )Can parallel 2-6 knots 18650 batteries!!!Non-battery: dry battery, battery, 1.2V rechargeable battery, NiMH battery, 3.2V Lithium Lithium Polymer battery.Add to Cart4.17€
-
10 Grid Digital Segment LED Light Bar 10 Flat Tube of Super Bright 2 Red+3 Yellow+4 Green+1 Blue Light Flat Tube ()10 Grid Digital Segment LED Light Bar 10 Flat Tube of Super Bright 2 Red+3 Yellow+4 Green+1 Blue Light Flat TubeAdd to Cart4.17€
-
New Led Ring 16x 5050 RGB LED Board with Integrated Drivers Module Geekcreit for Arduino - products that work with official Arduino boards ()16 ultra bright smart LED are arranged in a circle with 1.75" (44.5mm) outer diameter.The rings are 'chainable' - connect the output pin of one to the input pin of another. Use only one microcontroller pin to control as many as you can chain together!Each LED is addressable as the driver chip is inside the LED.Each one has ~18mA constant current drive so the color will be very consistent even if the voltage varies, and no external choke resistors are required making the design slim.Power the whole thing with 5VDC (4-7V works) and you're ready to rock.There is a single data line with a very timing-specific protocol.Since the protocol is very sensitive to timing, it requires a real-time microconroller such as an AVR, , PIC, mbed, etc.It cannot be used with a Linux-based microcomputer or interpreted microcontroller such as the netduino or Basic Stamp.As it requires hand-tuned assembly it is only for AVR cores but others may have ported this chip driver code so please google around.An 8MHz or faster processor is required.Comes as a single ring with 16 individually addressable RGB LEDs assembled and tested.Add to Cart7.14€
-
ESP32-CAMERA OV2640 ()- Ultra-small 802.11b/g/n Wi-Fi + BT/BLE SoC module
- Low-power dual-core 32-bit CPU for application processors
- Up to 240MHz, up to 600 DMIPS
- Built-in 520 KB SRAM, external 4M PSRAM
- Supports interfaces such as UART/SPI/I2C/PWM/ADC/DAC
- Support OV2640 and OV7670 cameras with built-in flash
- Support for images WiFI upload
-Support TF card
- Support multiple sleep modes
- Embedded Lwip and FreeRTOS
- Support STA/AP/STA+AP working mode
- Support Smart Config/AirKiss One-click distribution network
- Support for serial local upgrade and remote firmware upgrade (FOTA)
- Support secondary developmentAdd to Cart10.12€ -
4 x AA Battery Holder with wire ()This 4 "AAA" battery holder holds the batteries side-by-side and delivers 6VDC. It's ideal to use as a replacement or for project use.Add to Cart2.98€
-
KY-009-RGB-3-Color-Full-Color-LED-SMD-Module-for-Arduino-AVR-PIC KY-009-RGB-3-Color-Full-Color-LED-SMD-Module-for-Arduino-AVR-PIC KY-009 RGB 3 Color Full Color LED SMD Module for Arduino AVR PIC ()
KY-009 RGB 3 Color Full Color LED SMD Module for Arduino AVR PIC
Add to Cart4.17€ -
Voltage regulator 3.3V LDO MCP1700-3302E ()V REG, LDO + 3.3 V 250mA
The MCP1700-3302E/TO is a CMOS low dropout positive voltage regulator which can source up to 250mA of current with an extremely low input-output voltage differential of 178mV at 250mA. The low dropout voltage combined with the low current consumption makes this part ideal for battery operation.Applications
Power Management, Portable Devices, Automotive
Output Type:
Input Voltage Min:2.3V
Input Voltage Max: 6V
Fixed Output Voltage Nom.:3.3V
Output Current:250mA
Dropout Voltage Vdo:178mV
Operating Temperature Min:-40°C
Operating Temperature Max:125°CAdd to Cart0.83€ -
High quality LM1117 AMS1117 4.5-7V turn 3.3V DC-DC Step down Power Supply Module For Arduino bluetooth Raspberry pi ()
AMS1117 5.5V turn 3.3V DC-DC Step down Power Supply Module
Feature:
1.input: DC 4.5 V - 7 V (input voltage must high than output voltage 1 V above).
2. output: 3.3 V, 800 Ma (load current should not exceed 800 ma)
3. double panel design, layout beautiful and easy,
4. special design two row needles fixed hole, can be directly fixed on the hole plate for extended experiment;
5. input/output use 2 p single row needle , convenient connection;
6. PCB panel size: approx.2.5 cm * 1.1 cm
7. with indicator light (red)
8. weight is about: 1.6 g
package include:
1 x AMS1117 5.5V turn 3.3V DC-DC Step down Power Supply Module
Packed Safely in Bubble Bag.
Add to Cart2.98€ -
NeoPixel Stick - 8 x 5050 RGB LED with Integrated Drivers ()WS2812 NeoPixel Stick Strip 8 Way Serial 5050 RGB LED with Integrated Controllers UK Stock
Ideal for Arduino Projects, works great with Adafruit Neopixel Library
Description:
Control circuit and RGB chip are integrated in single 5050 package.
Each LED has built-in signal reshaping circuit.
Built-in reset circuit and power loss reset circuit.
Each pixel of primary color can achieve 256 brightness display
total 16777216 colors
Scan frequency not less than 400Hz.
Single Data Connection for all LEDs.
Maximum 5metres between LEDs without any extra circuitry.
30fps with 1024 pixels.
Send data at speeds of 800Kbps.
Internal Constant Current Source for consistent colours across all LEDs.Add to Cart5.95€ -
LM1117T-3.3 LM1117T LM1117 Low Dropout Voltage Regulator 3.3V ()This is the basic LD1117V33 voltage regulator, a low drop positive regulator with a 3.3V fixed output voltage.
This fixed regulator provides a great amount of stability and protection for your project and with its on ship trimming this regulator is able to reach an output voltage tolerance within ±1%.
Each one of these voltage regulators can output a max current of 800mA.
- Output Voltage: 3.3V
- Output Current: 800mA
- Dropout Voltage: 1V
- Internal Current and Thermal Limit
Add to Cart1.79€ -
LED breakout module ()This is a breakout board for the WS2812B RGB LED. The WS2812B (or "NeoPixel") is actually an RGB LED with a WS2811 built right into the LED! All the necessary pins are broken out to 0.1" spaced headers for easy bread-boarding. Several of these breakouts can even be chained together to form a display or an addressable string.Add to Cart4.17€
-
Aluminum Heatsink Cooler 14 x 14 x 6mm Adhesive Kit for Cooling Raspberry Pi ()Description: 14 x 14 x 6mm Aluminum Heatsink
Features:
Brand New and High Quality!
These heatsinks have a layer of thermal adhesive that allow for easy installation on to your board..
Just peel and stick.
Reduce the risk of hardware failure due to overheating.
Installation Instructions:
Make sure the chip modules are free from dirt and grease
Peel the protective liner off on the base of the heatsink
Apply the heatsinks to the corresponding chip modules and apply firm pressure.Add to Cart1.49€ -
2 Channel 5V Relay Module Arduino Compatible ()100% brand new and high quality
5V 2-Channel Relay interface board,and each one needs 15-20mA Driver Current
Standard interface that can be controlled directly by microcontroller
Equipped with high-current relay,AC250V 10A,DC30V 10A
Indication LED for Relay output status
Add to Cart4.17€ -
22402A-17 protoboard two sided 2x8 cm ()Quality PCB prototype board high quality glass fiber, Sturdy material. Well etched and well drilled. The holes are centered well and all pads are nicely tinned, when you stack the boards up you can see clear through. Tinned plated finish prevents oxidation, not easy to deformAdd to Cart3.45€
-
1 x AA Battery Holder with wire ()This 1 "AAA" battery holder holds the batteries side-by-side and delivers 1.5 VDC. It's ideal to use as a replacement or for project use.Add to Cart1.79€
-
1 Channel 5V Relay Module Arduino Compatible ()The module is uses SRD relay module to control high-votage elecrical devices. (maximum 250V).It can be used in interactive projects and can also be used to control the lighting, electrical and other equipments.It can be controlled directly by a wide range of microcontrollers and can be controlled through the digital IO port, such as solenoid valves, lamps, motors and other high current or high voltage devices.
Add to Cart2.96€ -
DC-DC Step Up Circuit Module 3V to 5V 1A ()1. Module Properties: non-isolated step-up module (BOOST)
2. Input voltage: 1-5V
3. Output voltage: 5.1~5.2V
4. Output Current: Rated 1A~1.5A (Single lithium battery input)
5. Conversion efficiency: up to 96% ( input voltage, the higher the efficiency )
6. Switching Frequency: 500KHz
7. Output ripple: 30mV (Max) 20M Bandwidth ( Input 4V, Output 5.1V 1A)
8. Voltage indication: LED lights with a load (input voltage is lower than 2.7V LED indicator off )
9. Operating temperature: Industrial grade (-40 Celsius to +85 Celsius )
10. Full load temperature rise: 30 Celsius
11. Quiescent Current: 130uA
12. Load regulation: ± 1%
13. Voltage regulation: ± 0.5%14. Dynamic response speed: 5% 200uS
Add to Cart2.62€ -
DC-DC Automatic Buck Boost Power Module Step Up and Down Board Input 3-15V Output 5V ()
- Type:
- Condition:
- Application:
- Supply Voltage:
- Dissipation Power:
- Model Number:
Feature:The DC-DC power module is automatically buck-boost to support the shutdown function.The maximum input voltage is 15VDC, the quiescent current is less than 200uA, the fixed output is 3.3V and the maximum output current is 600mA.Design work frequency of up to 1.2MHz, high stability, cost-effective, all industrial-grade components, long working voltage drift-free, suitable for demanding applications.Application:Widely used in communications equipment, digital radio, industrial motherboards, toys, model aircraft, microcontroller motherboards, household electrical appliances, automotive power supply, security monitoring, field collection, street lamps.Parameters:Input voltage: 2.5V-15VMaximum current: 600mAOutput voltage: 3.3VMaximum efficiency: 75%Package Included:
1 x DC-DC Automatic Buck Boost Power Module
Add to Cart5.36€ -
3.7V to 5V 2A 18650 Step-up Battery Module ()
- 1.4 level LED lights display power, intelligent automatic shutdown in non-working state;
2. Built-in lithium battery protection IC with overcurrent, overvoltage and undervoltage protection;
3. Dual USB output;
4, motherboard size: thickness 8mm * width 32mm * length 69mm.
Basic product parameters:
Input port: MicroUSB (Android port)
Input requirements: 5V constant voltage power supply can be used as charging input power, the most suitable charger is 5V1A or above
Output port: USB
Output parameter: 5V1A/5V2A
Add to Cart5.36€ - 1.4 level LED lights display power, intelligent automatic shutdown in non-working state;
-
FT232RL USB to TTL Serial Adapter Module ()
FT232RL FTDI USB to TTL serial adapter module for Arduino and other microcontrollers.
Specifications:- Interface: Mini USB
- Chip: FT232RL
- Indicator LEDs: RXD / TXD transceiver communication indicators
- Power: USB power supply, 5V or 3.3V selectable
- Pins: DTR, RXD, TX, VCC, CTS, GND
- Pitch: 2.54mm
- Size: 36 x 18mm (L x W)
Add to Cart4.40€ -
Raspberry Pi Heat Sink 3pcs ()
This heatsink set is specially designed for Raspberry Pi, it\'s function is to cool down the board and make your Raspberry operate safely
The Heatsink have a layer of adhesive on the back of them. Simply peel the adhesive off and stick onto your board
Reduce the risk of hardware failure because of overheating
Install Instructions:
Make sure the chip modules are free from dirt and grease
Peel the protective liner on the base of the heatsink
Affix the heatsinks on the chip modules and apply firm pressure
One set of aluminum heatsink
1pcs 14mm x 14mmx 6mm Heat sink
2pcs 8mm x 8mmx4mmAdd to Cart2.68€ -
New LED Ring 24 x WS2812 5050 RGB LED with Integrated Drivers ()24 ultra bright smart LED Ring are arranged in a circle with 66mm outer diameter. The rings are 'chainable' - connect the output pin of one to the input pin of another. Use only one microcontroller pin to control as many as you can chain together! Each LED is addressable as the driver chip is inside the LED.Add to Cart9.52€
-
MP1584EN Ultra-small size DC-DC step-down power supply module 3A adjustable step-down module super LM2596 ()
Features:
- Input Voltage : 4.5~28V
- Output voltage : 0.8V~20V
- Output Current : 3A(Max)
- Efficiency : 92%(Max)
- Switch Frequency : 1.5MHz(Max),1MHz(Typ)
- Operating Temperature : -20 to +85
- Size : 22mm * 17mm * 4mm
Add to Cart2.62€ -
Ultra-small LM2596 power supply module DC / DC BUCK 3A adjustable buck module regulator ultra LM2596S 24V switch 12V 5V 3V ()
- Name : LM2596 DC-DC Buck module
- Input voltage :4V ~ 35V
- The output voltage : 1.23V ~ 30V
- Output Current :3A( Max)
- Conversion efficiency:92%( MAX )
- Output ripple: <30mV
- Switching frequency: 150KHz
- Working temperature: -forty Five~ +85
- Size :43mm * 21mm * 14mm(Long*Width*Hight)
Features:
1. the range of input voltage: 3.2 V to 40 V dc (input voltage must be higher than to the output voltage of 1.5 V above. Can't booster)2. the range of output voltage: 1.25 V dc to 35 V voltage adjustable, high efficiency (92%) largest maximum output current is 3A.
Instructions:
1. Power (3-40V), power indicator light, the module is working properly.
2. Adjust the blue potentiometer knob (clockwise rotation generally boost,counter-clockwise rotationTurn down) and reach with a multimeter to monitor the output voltage required voltage.
Note:
Current work long hours is recommended for use in less than 2.5A, while adding bulkHeat sink (10W output above),because it is the step-down module, in order to ensure stable output Set,please keep the minimum 1.5V differential.
Add to Cart3.45€ -
MINI360 3A MINI DC-DC STEP DOWN CONVERTER VOLT REGULATOR 5V-23V TO 3. 6V 9V 12V ()
Size: 17*11*3.8mm
Color: multicolor
Material: electronic components
Input voltage: 4.75V-23V
Output voltage: 1V-17V
Output current: 3A peak, 1.8A for long time
Transfer efficiency: 96% (MAX.)
Switching freqnency: 340KHz
Output ripple: 30mV (no-load)
Load regulation: ±0.5%
Voltage regulation: ±2.5%
Working temperature: -40~85℃Package list:
1/5/10 x DC -DC power supply moduleFeatures:
< Efficiency: Up to 96% (depends on the difference between input and output voltage) This module uses synchronous rectification, efficient power conversion available.
< Good performance: Use integrally molded power inductor and synchronous rectifier control chip, small and efficient
< Wide application: Great for LED lights, micro-controllers, battery chargers, and most other low power devices.
< Compact and lightweight: It is compact and portable, high efficiency.Notes:
1. Please allowed 1-3mm differences due to manual measurement, thank you for your understanding!
2. Due to the difference between different monitors, please understand that the picture may not reflect the actual color of the item.Add to Cart3.81€ -
DC 0-30V 2 Wire LED Display Digital Voltage Voltmeter Panel Car Motorcycle ()Item specifics
- Display Type:
- Operating Temperature:
- Accuracy Class:
- Power Supply:
- Measuring Range:
- DIY Supplies:
- Dimensions:
- Model Number:
- Measuring range:
- Input range:
- Display:
- Measurement accuracy:
DESCRIPTION
DC 0-30V 2 Wire LED Display Digital Voltage Voltmeter Panel Car Motorcycle
Measuring range: DC 0.1V-30V
Input range: DC 2.7V-32V
Max Input: DC 32V. The device can be damaged if input is over 32V
Display: Three 0.36 "digital tube
Measurement accuracy: 0.1%
Refresh rate: about 300mS / times
Input impedance: About 100K
Screw holes measures :28mm
Operation Temp: -10 Celsius degree-+65 Celsius degree
Add to Cart4.64€ -
Aluminum Heatsink Cooler 10 x 14 x 6mm Adhesive Kit for Cooling Raspberry Pi ()Description: 10x 14 x 6mm Aluminum Heatsink
Features:
Brand New and High Quality!
These heatsinks have a layer of thermal adhesive that allow for easy installation on to your board..
Just peel and stick.
Reduce the risk of hardware failure due to overheating.
Installation Instructions:
Make sure the chip modules are free from dirt and grease
Peel the protective liner off on the base of the heatsink
Apply the heatsinks to the corresponding chip modules and apply firm pressure.Add to Cart1.49€ -
5V ESP8266 2 Channel WiFi Relay Module ()1. Onboard ESP-01 WiFi module and high performance microprocessor STM8S103.
2 The module has 2 working modes:
Mode 1: The phone is directly installed on the WiFi module.
Mode 2: Equipped with a mobile phone and WiFi module on the router
Additional features: It can also be used as a USB relay when the ESP-01 is pulled out.
3. Transmission distance:
In an open environment, when the mobile phone is installed on the WiFi module, the maximum stable transmission distance is 100M.
4. When the WiFi module and the mobile phone are simultaneously carried on the router, the transmission distance depends on the signal strength of the router.
5. On-board 5V, 10A // 250V AC 10A // 30V DC relay, which can continuously pull 100,000 times, with diode discharge protection and short response time.
6. Use Smartcongig technology to complete the account and password configuration on the APP ESP-01 WiFi module on the mobile phone, and configure the username and password memory functions.
7.Board mode selection and real-time working status indicator.
8. Reserved UART debug interface and STM8 SWIM program download interface.
9. Board size: 59 * 40mmAdd to Cart7.74€ -
400 point interlocking breadboard ()Transparent
• One terminal strip, 300 Tie-Points
• Two distribution strips, 100 Tie-Points
• ABS Plastic material
• Completely reusable
• Coordinates for easy component placement
• Accepts a variety of wire sizes (20-29 AWG)
• Dimensions: 82mm x 106mm x 8.5mmAdd to Cart4.64€ -
3.3V 5V 12V Multi Output Voltage Conversion DC-DC 12V to 3.3V 5V 12V Power Module I83 ()1 .Input: DC 6V - 12V (input voltage must be higher than the output voltage to 1V or more.)2. Output: 3.3V (+ - 0.05v error), 5.0V (+ - 0.05v error), 800mA (load current can not exceed 800ma), 12V (12V input directly to output)3. Pairs of panel design, layout, nice;4.Specially designed two pin mounting holes, can be directly fixed to the tunnel plate to extend the experiment;5 Using a plurality of input and output pin, easy to use and connect;6 PCB board size: 4.5cm * 4.5cm7 With power indicator light (red)Add to Cart4.17€
-
1.5V 1.8V 2.5V 3V 3.3V 3.7V 4.2V to 5V DC-DC Step Up Module 3.3V ()3.3V output version:
The input voltage is 0.8-3.3v; Output voltage 3.3V
Output current: 500 mA
The starting voltage is 0.8V and the output current is 10mA
Input 1-1.5v, output 3.3V, 50-110ma;
Input 1.5-2v, output 3.3V, 110-160ma;
Input 2-3v, output 3.3V, 160-400ma;Add to Cart2.62€ -
Flashing Cable of CH340G USB to TTL Module ()USB To TTL Serial Adapter Module Upgraded Download Cable CH340 Chipset for WinXP
Features: 100% brand new and high quality
This is a newly designed product that uses the CH340 chip.
The CH340 provides a convenient solution for connecting a RS232-like full-duplex asynchronous serial device to any universal serial bus (USB) host.
The CH340G is perfectly compatible with WinXP/98/VISTA/7/8/systems and can emulate on most operating systems, allowing existing applications based on COM ports to be easily ported and USB connected without having to rewrited COM The port software applies a traditional COM port.
The cable mainly used in MCU serial communication, can be used in 51SCM, ARM and other application scenarios.
Ideal USB debugs cord for Vendor ID re-write, router, GPS, set top box, flash firmware on hard drive, etc.
Specifications: Material:ABS
Color:Black
Length:Approx. 100cm/39.37 inchesAdd to Cart3.21€ -
FT232 USB To TTL Flash Line With CTS RTS ()FT232 USB to TTL serial adapter 3.3V (6 pin 0.1” pitch female socket header) connects devices with 3.3 V logic level UART signals interface to a laptop via USB port
A genuine FT232RL chip module is housed in USB 2.0 type A male terminal for wider compatibility and supports reliable data transfer rates
FTDI USB to TTL serial cable 3V3 (6 way outputs) provides access to Tx, Rx, RTS#, CTS#, VCC (5v) and GND (power line provides 5V and data signal is at 3.3V)
FTDI chipset on the PCB board has configurable internal EEPROM and UART signals can be individually inverted by configuring the EEPROM
6 pin header TTL to USB converter cord is compatible with Windows 11, 10, 8, 8.1, 7 (32, 64-bit), 2008/XP/Vista/CE, Mac OS, Linux 2.4 and greater; ideal USB 2.0 debug cord for Vendor ID re-write, router, GPS, set top box, transmitter, flash firmware on hard drive, etc.Add to Cart5.59€ -
Passive Buzzer Module for Arduino ()
Description:
-
No oscillation source,need square wave(frequency 2K-5K ) to drive
Audino 9012 drive;
Work Voltage:3.3-5V
Set bolt hole, easy to assemble
PCB Dimension:3.3cm*1.3cm - Pin Definition :
- Pin definition
- Vcc : 3.3-5v
- GND : The Ground
- I/O : I/O Interface of SCM
Package includes: -
20cm 1p-1p DuPont line x 3pcs
-
Passive Buzzer Module X 1pcs
Add to Cart4.75€ -
No oscillation source,need square wave(frequency 2K-5K ) to drive
-
4x4 16 key matrix mebrane keypad ()
- Product Name : Membrane Switch;Key Type : 4x4;Voltage : DC 12V
- Current : 30mA;Contact Resistance : >=100 Ohm;Force : 250-350g
- Contact Bounce : >1s;Pad Size : 76 x 69 x 0.8mm/3'' x 2.7'' x 0.03''(L*W*T);Cbale Length : 72mm/2.8''
- Connector Pitch : 2.54mm/0.1'';Material : Plastic;Color : As Picture Shown
- Weight : 9g;Package Content : 1 x Membrane Switch
Add to Cart3.90€ -
Microphone Sensor AVR PIC High Sensitivity Sound Detection Module ()
Features: 100% Brand new and high quality For sound detection module has two outputs: 1. AO, analog output, real-time output voltage signal of the microphone 2. DO, when the sound intensity reaches a certain threshold, the output high and low signal Module features: 1. There is a mounting screw hole 3mm 2. The use 5v DC power supply 3. With analog output 4. There are threshold level output flip 5. High sensitive microphone and high sensitivity. 6. A power indicator light 7. The comparator output is light
Add to Cart4.75€ -
170 tie point mini breadboard white ()170 tie point breadboard - White
• 17 x 5 x 2 points
• ABS plastic material
• Completely reusable
• Coordinates for easy component placement
• • Accepts a variety of wire sizes (20-29 AWG)
• Dimensions: 45mm x 34.5mm x 9.5mmAdd to Cart3.45€